OTHER

GEL-PAS




PASSIVATION GEL FOR WELDS, METAL SHEETS AND STAINLESS STEEL DETAILS



1. Intended use

Gel-Pas is a paste of gel consistency, developed for active etching and passivation of stainless steel and welds with the use of a brush or by spraying. Gel allows to apply the passivation paste in any condition.

2. Application

– In order to etch the weld, apply with a brush a uniform (not too thin) layer of gel onto the weld and stained area around it. The etching time varies from few minutes to half an hour, depending on the ambient temperature and carbon deposit thickness. It is advised for the user to check the necessary application time, taking into consideration their requirements. When the etching is over, flush thoroughly with a cold water jet, preferably under pressure. Do not use hot water.

– In order to etch the surface, apply the gel uniformly with the sprayer. In order to be sprayed, the product may be diluted with distilled water. Do not use the tap water, since it contains mineral salts which neutralize acids – impairing the product performance.Whentheetchingisover,flushthesurfacethoroughlywithcoldwater.

During warm months, it is advised not to expose the products subject to Gel-Pas etching to direct sunlight. Moreover, it is advised to perform the etching in a place protected against the rain.

It is advised to thoroughly degrease the detail prior to commencing the etching process (e.g., with Steeler Max – degreaser). When the etching process is over, it is recommended to restore the protective surface oxides to their original condition with the use of a passive product for steel or by using the Gel Pas Max again on the etched surface.


Poliprotect




ECOLOGICAL, INSOLUBLE PEELABLE POLYMER FILM



1. Intended use

– for protection of e.g., paint workshop walls, surfaces exposed to dirt

2. Properties

– resistant to all solvents;
– has very good adhesive properties;
– this product is a water solution of fully biodegradable polymers;
– does not contain silicone;
– easy application;
– can be significantly diluted with water; then forms the film washable under pressure;
– 20 m is a minimum threshold value of peelability, best results achieved at 50 m.

3. Application

– surface should be degreased prior the application.
– stir the preparation and do not dilute it with water.
– apply liquid product by brush, flock roller or hydrodynamic pump, trying to achieve a uniform layer.
– then wait for it to dry completely for 30 – 50 min depending on the ambient condition. Repeat the action if necessary.
– carefully peel off the formed film together with applied stains, not allowing it to break. Used material can be dissolved in water. Filtrate and dispose of separated soiling as paint shop waste.


Defoamer




BIODEGRADABLE, HIGHLY EFFICIENT ANTIFOAMING AGENT



1. Intended use

DeFoamer in form of dilutable water emulsion is a highly concentrated antifoaming agent intended for the foam elimination. It efficiently helps to eliminate foam in industrial processes:
– paper manufacturers;
– degreasing lines;
– paint shops;
– industrial washes;
– scrubbing machines;
– wastewater treatment plants;
– and any other place when foam is unwanted.

2. Properties

– soluble in water in rates dependent on the quantity of foaming agents added to the bath in question;
– does not cause corrosion or deposits; – does not contain any solvents
– biodegradable

3. Application

– usually applied with the use of a pump on production lines;
– concentratecanbeaddedtothebath,whileobserving theefficacyoffoamelimination;
– dilution with water:
– pump 0.01% – 0.1%


MASBIT BIO




MASBIT BIO ECOLOGICAL, HIGHLY EFFECTIVE ANTI-ADHESION DILUTABLE AGENT PREVENTING THE ASPHALT ADHESION



1. Intended use

Masbit in form of water emulsion prevents the adhesion of bituminous mass to the surfaces of machines and devices. It replaces petroleum and other preparations based on mineral oils.

2. Properties

– dissolves in water max 1:10 forming emulsion
– does not cause corrosion
– does not contain any mineral oils – biodegradable

3. Application

– add Masbit Bio to water simultaneously stirring the mixture e.g., stirring continuously, add slowly app. 100 – 150 liters of MasbitBio to 850 – 900 liters of water etc
– spray onto the surface of machines and devices
– spray onto the surface of asphalt prior to driving on it – or can be diluted in automatic feeding machine.


Zender




PREPARATION FOR REMOVING HIGH-TEMPERATURE OXIDES



Alkaline preparation used to remove and dissolve the effects of gas corrosion and metal oxide layers, based on washing aids substances and safe surfactants.

Removes scale and slag formed on the surface of heated metal objects as a result of their contact with air. Removes the scale in the form of coatings or scales.

It contains special ingredients that do not cause aluminium etching and black steel corrosion inhibitors, as well as compounds that soften any deposits.

The preparation is used to wash aluminium and cast iron heads of car engines.
Use diluted 1: 10- 1:20. Strongly foaming, two-phase preparation.
The preparation after dissolving scale should be flushed with water and protected against corrosion


Top